Hunter Air Purifier - QuietFlo 30170 Users Manual
Programming
Setting Day and Time
Setting the correct day and time allows the programs to work effectively and provides a clock for your reference. Although the instructions for setting the day and time are listed under Initial Operation, they are repeated below for your convenience.
Adjusting Day and Time: (For example, Wednesday at 3:45 pm)
To set the day or time, press the DAY/TIME key. All display features except the day and time will go blank and the hour will flash.
- Use the UP/DOWN keys to adjust the hour. Tapping the key will advance the hour by increments of one. Holding down the key will change the hour rapidly. Note the AM/PM indicator as you cycle through a 24 hour period.
Press the DAY/TIME key again. Now, the minutes will be flashing. Use the UP/DOWN keys to adjust the minute. Tapping the key will change the minute by increments of one and holding the key will change the minute rapidly.
Press the DAY/TIME key to accept the minute setting and go to the day of the week. Use the UP/DOWN keys to set the current day.
Press the DAY/TIME key a final time to accept the day setting and return to Normal mode.
NOTES:
- The clock flashes when the time has not been set.
- At any time while you are setting the Day/Time, you can press the PROGRAM key to toggle between AM/PM format and military time format.
- To quickly exit the Day/Time setting mode, you can press the DISPLAY key or wait 15 seconds without pressing any keys.
- The time displayed will be frozen in Day/Time setting mode; however, the internal clock is still running. If no value is changed, then the frozen time will be replaced by the internal clock when you exit the Day/Time setting mode.
- If the power is lost to the unit, the memory will maintain the clock for at least 12 hours.
Pre-set Programming
As discussed in the Manual and Auto Operating Modes section of the manual (pg. 9), your air purifier comes with pre-set programs. For your reference, these programs are listed again below. When you turn your air purifier to Auto Mode, these programs are active unless you override them with your personalized programs. Refer to the next section, User Programming, to learn how to input your own programs.
Table 3: Pre-set programming provided for each air purifier.
User Programming
User programming allows you to set when the air purifier is on and what blower speed to
use. You may define up to 4 programs for the weekdays and up to 4 programs for the weekend.
Before starting the programming process, first you should determine what times and
blower speeds will best fit your needs. Use the charts below to organize and record the
programs that you desire. Use a pencil so you can revise your records each time you change
the programs.
NOTES:
- Setpoint time is the time at which the blower speed will change. The specified blower speed will be active until the next setpoint time is reached.
- The setpoint time can only be set in 10 minute increments.
- Blower speed ranges from 0 to 3. Zero indicates that the blower is turned off, a setting of 1 is low, 2 is medium, and 3 represents a blower speed of high.
- If you want the weekdays and the weekends to be identical, you should program both the weekday programs and the weekend programs with the same values.
- If you use less than 4 programs, set the unused programs identical to one of the other programs. Table 5 below gives an example where programs 3 and 4 are identical.
Table 5: Using 3 of the 4 Available Programs
To set or change the programs:
Press the PROGRAM key. Program 1 for weekdays will be shown with the hour position flashing to denote that you should set that value now.
- Use the UP/DOWN keys to adjust the hour setting. Once set, press the PROGRAM key again.
Now, the minute position will be flashing. Use the UP/ DOWN keys to adjust the minute setting in 10 minute increments. Press PROGRAM to accept the value.
Finally, the blower speed will be flashing. Use the UP/ DOWN keys to adjust the blower speed setting from 0 to 3. Zero indicates that the blower is turned off, a setting of 1 is low, 2 is medium, and 3 represents a blower speed of high. Press PROGRAM to accept the blower speed setting. This completes the first program for weekdays.
- The display will advance to the second program for weekdays with the hour position flashing. Follow steps 2 to 4 to set the second program. After setting each program, the display will advance to the next program number. After going through all four weekday programs, the unit will advance through each of the four weekend programs. The adjustment procedure (steps 2 to 4) is the same for each program.
NOTES:
- For fast advance of the values, press and hold the UP/DOWN keys for 2 seconds. The values for program time or blower speed will advance quickly.
- To exit programming mode and return to normal operating mode, either wait 15 seconds without any key presses or press DISPLAY to immediately return to normal operating mode.
- Once entered, the programs are active and stored in the unit’s memory. You can unplug and move the air purifier and still retain the programs.
Reviewing Programs
You may want to review the programs to confirm that the settings are still acceptable. The following steps show you how to review the programs.
To review programs:
- With the air purifier On, press and hold the PROGRAM key. After 2 seconds, the display will advance through the 4 programs for weekdays and then the 4 programs for the weekend. You must hold the PROGRAM key as the display reviews the programs.
- After viewing all programs, the display will return to normal operating mode and you can release the key.
NOTE:
- If you review a program that you want to change, simply release the PROGRAM key. The display will stop on that program and allow you to make changes. Refer to User Programming (pg. 14) for more details on how to change the values.
Locking/Unlocking the Keypad
Once you enter the desired programs, you may want to lock the keypad to prevent accidental changing of the programs. When the keypad is locked, all keys will be disabled. If you press a key, “Lock” will be displayed on the screen for 1-2 seconds.
To Lock or Unlock the Keypad:
To lock the keypad, press and hold the UP/DOWN keys simultaneously for 2-3 seconds. The display will read “ Lock” for 1-2 seconds.
- To unlock the key pad, press and hold the UP/DOWN keys simultaneously for 2-3 seconds. The keypad will be functional.
Resetting the Air Purifier
In the unusual situation that the unit or the display is exhibiting erratic behavior, you may want to reset the air purifier. Since you will loose all of your programmed settings when the unit is reset, you should consult the Troubleshooting section (pg. 21) of the manual to resolve the problem before using the Reset Feature. When the unit is reset, the clock, day of the week, and programs will default to their factory settings and the unit will turn off. The only information that will be saved is the pre-filter and filter counter values. If you still have problems after resetting the air purifier, please contact Hunter for additional assistance (refer to Technical Assistance pg. 21).
To Reset the Air Purifier:
- Using a small pin or paperclip, hold down the RESET key for 2 seconds or until the display goes blank.
- Follow the directions in the Programming section of the manual (pg. 12) to update the day, time, and programs of the unit.
<- Operation
